NI MASCHINE MK3 STAND - 15 degrees - 3D printed - 100% Buyer Satisfaction

Description

3D Printed 15 degrees tilted STAND with rubber pads for NI MASCHINE MK3
This is a low height design with
15 degree tilt.
This allow you to use Maschine MK3
on your desk more ergonomic layout
and it may affect about longer flow state when writing music.
- It is
portable, easy to detach and attach again
- You can bring it to your live gig - forget the heavy laptop stands and weird unstable things.
This system has 2 pieces,
just slip them from the correct sides
.
1 leg with hole for the left and 1 leg with cut-out for the right side.
You can handle power button, and phones volume knob with this stand.
It will be tight enough to stand perfect on your desk without slip or wobble.
Pros:
Very stable!
Really lightweight and strong enough.
There is no connecting rod at the rear
.
Together with these legs, you can handle the  as a cohesive system without worrying about it falling apart.
It is
portable, easy to detach and attach again
You can bring it to your live gig - forget the heavy laptop stands and weird unstable things.
Cons:
Unfortunately decksaver is not fully compatible with this stand, but if you can put on that carefully on Maschine it may save your device against dust or spill liquids with no problem.
MAIN FEATURE: It will be tight enough to stand perfect on your desk without slip or wobble.
-----------------------------------------
About st3nD tabletop stands:
All products are made with 3D printing, followed by some post-processing: deburring, sanding, surface cleaning.
The main goal
is to develop and manufacture high quality table
stand
s with the following features:
Easy
installation without glueing,screws or any tools.
Stable feel,
no sliping, free of wobbling.
Easy handle the stand and your device together as a
cohesive system
without worrying about falling apart when moving.
The system
don't take up more space sideways
like the device own.
Really
lightweight
and strong enough.
No middle rods or any stabilizers.
Portable
so you can bring it to your live gig easily.
These are the considerations I keep in mind when design and making stands.
I try to lower prices as low it possible for save your bucks but look after the quality too. I manufacturing these products one by one. So these handmade stands are different than mass products. This is the reason why they are not so so cheap as I want it too. I will make the stand for you, just for you, so you can focus using your device more ergonomic.
Please check my other stands for various brands as
: Native instruments, Maschine, Ableton, Roland, Akai, Arturia, Elektron, Novation, Roland Boutique Series, Presonus
https://www.ebay.com/str/st3nd
IMPORTANT:
The device is only an illustration for the stand, which is not part of the sale
Shipping is depend printing que, printing time, and your country distance and shipping conditions (please be patient due covid delays :) )
20° tilted STAND with rubber pads for PRESONUS FADERPORT 8 DAW controller
Forget the heavy or big laptop stands and weird unstable things like books to lift your beauty Faderport.
This stand allow you to use PreSonus Faderport 8 on your desk more ergonomic and
READ BETTER THE LITTLE DISPLAYS.
Stable feel,
no sliping, free of wobbling.
Easy
installation without glueing,screws or any tools.
Easy handle the stand and your device together as a
cohesive system
without worrying about falling apart when moving.
The system
don't take up more space sideways
like the device own.
Really
lightweight
and strong enough.
No middle rods or any stabilizers.
Installation:
Due to the design of the device, the placement of the legs is a bit tricky but VERY EASY! First, hook the lower claws into the lower edge of the Faderport so that the foot runs parallel along the rubber feet of the device. Once the lower part is stuck, pull and lift the rear claws over the upper edge at the same time, then release the upper claw. The spring force of the upper strong clip keeps the foot tight. The recesses surrounding the faderport’s own rubber feet prevent the foot from sliding to the side. No matter which foot you place first those are swappable because both feet are punched in the same way to access the power button.
Pros:
Very stable!
Really lightweight and strong enough.
There is no connecting rod at the rear
.
Together with these legs, you can handle the  as a cohesive system without worrying about it falling apart.
It is
portable, easy to detach and attach again
Cons:
-
Not fully compatible with Decksaver, but can be placed on top of the device to prevent dust from collecting on the device
MAIN FEATURE: It will be tight enough to stand perfect on your desk without slip or wobble.
-----------------------------------------
About st3nD tabletop stands:
All products are made with 3D printing, followed by some post-processing: deburring, sanding, surface cleaning.
The main goal
is to develop and manufacture high quality table
stand
s with the following features:
Easy
installation without glueing,screws or any tools.
Stable feel,
no sliping, free of wobbling.
Easy handle the stand and your device together as a
cohesive system
without worrying about falling apart when moving.
The system
don't take up more space sideways
like the device own.
Really
lightweight
and strong enough.
No middle rods or any stabilizers.
Portable
so you can bring it to your live gig easily.
These are the considerations I keep in mind when design and making stands.
I try to lower prices as low it possible for save your bucks but look after the quality too. I manufacturing these products one by one. So these handmade stands are different than mass products. This is the reason why they are not so so cheap as I want it too. I will make the stand for you, just for you, so you can focus using your device more ergonomic.
Please check my other stands for various brands as
: Native instruments, Maschine, Ableton, Roland, Akai, Arturia, Digitakt, Novation, Roland Boutique Series
https://www.ebay.com/sch/gabvarg-0606/m.html
IMPORTANT:
The device is only an illustration for the stand, which is not part of the sale
Shipping is depend printing que, printing time, and your country distance and shipping conditions (please be patient due covid delays :) )